iXtreme LT+ Lite Touch Xbox 360 Drive Firmware Flashing
Page 1 of 3 123 LastLast
Results 1 to 10 of 23
  1. #1
    Loyalist
    Join Date
    Jan 2013
    Location
    Sunny Kent, UK
    Posts
    443
    Thanks
    26
    Thanked 53 Times in 50 Posts

    Black Screen After Xbox Boot Logo..

    Ok, so where to start, I'll keep it as short as I can.

    I RGH'd my Jasper (256MB) the other day, got it all working fine, got Xell to boot, got CPU Key.

    I then used J-Runner to build a Glitched 16202 Dash with DashLaunch Patches ticked, and flashed it to the NAND (waited 30 seconds or more) I selected the correct Motherboard.

    I booted console and it booted into the new glitched dash fine. I stuck in my USB which I had prepared using Charincol's guide on here. Went into USB and Demo and copied over FSD Installer.

    Went into the Games tab and selected FSD Installer and then the screen went black, and ever since, every time I boot my Xbox up it loads up to the Xbox Boot Logo and then goes to a black screen.

    I can boot into Xell no problem by hitting the eject button.

    I reflashed my original NAND Dump (I done 4, no bad blocks etc) and now I either get 3 red lights with 0022 secondary error, or it gets a short way into the Xbox Boot Logo and then goes black screen again..

    Any advice?
    Last edited by lockett85; 03-17-2013 at 07:33 PM.
    A little thanks goes a long way

    Everything you could ever need to download is on this forum..

    >>>Here!<<<


  2. #2
    Legend
    Join Date
    Nov 2010
    Location
    Colorado
    Posts
    4,268
    Thanks
    25
    Thanked 732 Times in 542 Posts
    When you flashed the original back, did you disable the Coolrunner before booting it?
    I'm only smart cause I did it every wrong way already.

    Reset Glitch Hack (RGH) Guide

    Why not to spoof drives
    Pro Jtag/RGH/R-JTAG installs, DVD key retrieval/LTU flashing, Drive flashing: Local if in greater Denver


    If you followed a half-assed way to back up your XGD3 game disc, you deserve all the trouble you're getting.


    "Make it idiot proof and someone will make a better idiot."

  3. #3
    Loyalist
    Join Date
    Jan 2013
    Location
    Sunny Kent, UK
    Posts
    443
    Thanks
    26
    Thanked 53 Times in 50 Posts
    Without desoldering the CoolRunner I switched the switch to NOR (I read it stops it from glitching, not sure if this is correct?) I get the above happen, I switched it back on and put the switch on Phat and I get a short boot logo and then it just freezes up, although out of pure curiosity, I switched the switch to Slim and it boots fine into the original NAND.

    I tired again to flash my NAND back to 16202 with a fresh build though J-Runner and I get the same, the Xbox Logo comes up and after it finishes the screen just goes blank. I tried to switch from Phat to Slim, but the green light won't flash when its set to Slim.

    I got a decent understanding of this I would say, albeit my first attempt, but I'm stumped.
    A little thanks goes a long way

    Everything you could ever need to download is on this forum..

    >>>Here!<<<


  4. #4
    Legend
    Join Date
    Nov 2010
    Location
    Colorado
    Posts
    4,268
    Thanks
    25
    Thanked 732 Times in 542 Posts
    NOR is what it should be when glitching. PROG disables it. Flash the original Nand back and see if it boots on PROG.
    I'm only smart cause I did it every wrong way already.

    Reset Glitch Hack (RGH) Guide

    Why not to spoof drives
    Pro Jtag/RGH/R-JTAG installs, DVD key retrieval/LTU flashing, Drive flashing: Local if in greater Denver


    If you followed a half-assed way to back up your XGD3 game disc, you deserve all the trouble you're getting.


    "Make it idiot proof and someone will make a better idiot."

  5. #5
    Loyalist
    Join Date
    Jan 2013
    Location
    Sunny Kent, UK
    Posts
    443
    Thanks
    26
    Thanked 53 Times in 50 Posts
    Sorry. That is totally my mistake. It is set to NOR for glitching, not PRG.

    I done the above, my NAND is currently flashed to my original, I set it to PRG and it just freezes half way though the boot animation.
    A little thanks goes a long way

    Everything you could ever need to download is on this forum..

    >>>Here!<<<


  6. #6
    Legend
    Join Date
    Sep 2011
    Location
    Birmingham UK
    Posts
    1,280
    Thanks
    81
    Thanked 163 Times in 159 Posts
    Is this RGH1 or RGH2?
    1. The first rule of Jungleflasher is.... you always save your key first.
    2. The second rule of Jungleflasher is.... YOU ALWAYS SAVE YOUR KEY FIRST!!!

    Studies have shown that using the "Thanks" button increases both length and girth

    Flashing/Glitching Xbox 360's in Birmingham, UK
    Feedback from satisfied customers

  7. #7
    Loyalist
    Join Date
    Jan 2013
    Location
    Sunny Kent, UK
    Posts
    443
    Thanks
    26
    Thanked 53 Times in 50 Posts

    Black Screen After Xbox Boot Logo..

    RGH1 mate

    Edit: So I went to bed last night, everythings been off for 7 hours or so, turned on Xbox, booted right up to the Glitched NAND..... ??Confused??

    Edit 2: Left it sitting on the dash for about 10 minutes while I sorted some stuff out. The console is not responding to controller inputs now. And when rebooting I get the black screen again Lol wtf.
    Last edited by lockett85; 03-18-2013 at 05:27 AM.
    A little thanks goes a long way

    Everything you could ever need to download is on this forum..

    >>>Here!<<<


  8. #8
    Legend
    Join Date
    Sep 2011
    Location
    Birmingham UK
    Posts
    1,280
    Thanks
    81
    Thanked 163 Times in 159 Posts
    Its beginning to sound like a RROD error creeping in - its very rare on a Jasper but it does happen. Had one that did the exact same thing i.e freezing, and a reflow sorted it out nicely. Might be worth considering.

    Actually before you do any reflow, try loading up the original nand in JRunner, then creating a retail nand for whatever dash version its currently on ( to retain your RGH1), and see if it improves the situation, if so, go forth to create a glitch image from that and test again.
    Last edited by Methtical; 03-18-2013 at 05:58 AM.
    1. The first rule of Jungleflasher is.... you always save your key first.
    2. The second rule of Jungleflasher is.... YOU ALWAYS SAVE YOUR KEY FIRST!!!

    Studies have shown that using the "Thanks" button increases both length and girth

    Flashing/Glitching Xbox 360's in Birmingham, UK
    Feedback from satisfied customers

  9. #9
    Loyalist
    Join Date
    Jan 2013
    Location
    Sunny Kent, UK
    Posts
    443
    Thanks
    26
    Thanked 53 Times in 50 Posts
    Is that likely though seeing as I can sit in Xell for as long as I want? About 20 minutes at the moment.

    Still if thats the case this box is a loss. I picked it up cheap hoping to turn a profit, but with having to pay for a reflow that won't happen haha.

    Edit: So I got my console sitting here working fine with the original NAND flashed back, but ONLY if I have the CR set to NOR and switched to SLIM..

    Is this strange or what.
    Last edited by lockett85; 03-18-2013 at 06:36 AM.
    A little thanks goes a long way

    Everything you could ever need to download is on this forum..

    >>>Here!<<<


  10. #10
    Legend
    Join Date
    Sep 2011
    Location
    Birmingham UK
    Posts
    1,280
    Thanks
    81
    Thanked 163 Times in 159 Posts
    Yeah Xell can boot despite GPU errors as it doesn't utlilise it the same way as booting dashboard I'm led to believe.

    Have you tried recreating the retail nand and flashing that back yet?
    1. The first rule of Jungleflasher is.... you always save your key first.
    2. The second rule of Jungleflasher is.... YOU ALWAYS SAVE YOUR KEY FIRST!!!

    Studies have shown that using the "Thanks" button increases both length and girth

    Flashing/Glitching Xbox 360's in Birmingham, UK
    Feedback from satisfied customers

Page 1 of 3 123 LastLast

Similar Threads

  1. Burned games all boot to a black screen, forcing hard reset. Help!
    By shatenfreude in forum iXtreme LT+ Lite Touch Firmware Phat Support
    Replies: 6
    Last Post: 07-22-2012, 06:34 PM
  2. Xbox logo just stays on screen
    By devils in forum Open Forum
    Replies: 3
    Last Post: 10-07-2011, 12:21 PM
  3. Disk is recognised in the dashboard but when boot shows black screen
    By 1337Fear in forum iXtreme LT+ Lite Touch Firmware Phat Support
    Replies: 14
    Last Post: 06-18-2011, 02:22 PM
  4. [Solved] Long Boot / Black Screen Before loading (backup)
    By adsense in forum iXtreme LT+ Lite Touch Firmware Phat Support
    Replies: 16
    Last Post: 02-08-2011, 01:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
1e2 Forum