iXtreme LT+ Lite Touch Xbox 360 Drive Firmware Flashing
Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Up and Coming Legend
    Join Date
    Jan 2010
    Location
    Surrey, UK
    Posts
    862
    Thanks
    17
    Thanked 71 Times in 71 Posts

    xenon rgh - green cr light not flashing

    Hey, i have been trying to do rgh on my xenon to get the dvd key but i just can't get the green light on the cr to flash.
    I have tried going over all my points and changing the pll_bypass cable all to no avail. the only thing left to try is to try differen't values of cap between gnd and pll_bypass

    will post some pics of soldering once the camera has charged (since my iPhone has decided not to focus)

  2. #2
    DGX
    DGX is offline
    Xtreme Helper
    Join Date
    Nov 2010
    Posts
    201
    Thanks
    7
    Thanked 19 Times in 19 Posts
    Did you try using the shielded cable instead of the blue one? Also I'm assuming you set the CR to RGH1 configuration?

  3. #3
    Up and Coming Legend
    Join Date
    Jan 2010
    Location
    Surrey, UK
    Posts
    862
    Thanks
    17
    Thanked 71 Times in 71 Posts
    yes i always use shielded cable, and yep, the cr is flashed with the rgh 1 files

  4. #4
    Up and Coming Legend
    Join Date
    Jan 2010
    Location
    Surrey, UK
    Posts
    862
    Thanks
    17
    Thanked 71 Times in 71 Posts
    hmm... now i have the green light flashing. but sometimes it is for a full secondm an sometimes it is for like .25 of a second (always 5 between flashes tho)

  5. #5
    DGX
    DGX is offline
    Xtreme Helper
    Join Date
    Nov 2010
    Posts
    201
    Thanks
    7
    Thanked 19 Times in 19 Posts
    I meant the jumper's configuration . . .

  6. #6
    Up and Coming Legend
    Join Date
    Jan 2010
    Location
    Surrey, UK
    Posts
    862
    Thanks
    17
    Thanked 71 Times in 71 Posts
    there's a jumper on it? the cr is just as you sent it to me (and everything looked the same as the one in my jasper, which is using rgh 1)

  7. #7
    DGX
    DGX is offline
    Xtreme Helper
    Join Date
    Nov 2010
    Posts
    201
    Thanks
    7
    Thanked 19 Times in 19 Posts
    Look @ the picture below and make note of the two red rectangles marked 1 & 2.


  8. #8
    Up and Coming Legend
    Join Date
    Jan 2010
    Location
    Surrey, UK
    Posts
    862
    Thanks
    17
    Thanked 71 Times in 71 Posts
    getting the "do not hotlink" message. However i just got it to glitch, took over 30 mins. of course i forgot to plug the network cable in, and being too lazy to type in that long cpu key i just rebooted it with the cable plugged in, this could take a while

    also, since i know this has the no dvd flag, is there any good guides to building a clean nand?
    Last edited by max1zzz; 08-09-2012 at 06:46 PM.

  9. #9
    DGX
    DGX is offline
    Xtreme Helper
    Join Date
    Nov 2010
    Posts
    201
    Thanks
    7
    Thanked 19 Times in 19 Posts
    Try 360 Multi builder for creating a retail image. Also xenons are pain in the a$$ to glitch, some take hours let alone 30 mins.

  10. #10
    Up and Coming Legend
    Join Date
    Mar 2012
    Location
    San Antonio
    Posts
    644
    Thanks
    0
    Thanked 80 Times in 79 Posts
    Just a dumb suggestion, I only make it because I was about to trash a xenon until I realized this - The wire near the ANA chip, is on the pad AWAY from the ana chip, not the one near it.

    This is the opposite from every other console. (Where the proper pad, is the one next to the HANA)

Page 1 of 2 12 LastLast

Similar Threads

  1. Flashing Green light
    By yanv in forum Open Forum
    Replies: 6
    Last Post: 12-09-2011, 02:55 AM
  2. Green light flashing
    By John Mc Grath in forum Open Forum
    Replies: 10
    Last Post: 12-03-2011, 03:24 PM
  3. Flashing green light
    By TWITDADDY in forum Open Forum
    Replies: 3
    Last Post: 06-16-2011, 11:11 AM
  4. Xbox 360 Flashing Green Light
    By atlantabound in forum Open Forum
    Replies: 5
    Last Post: 03-17-2010, 02:39 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
1e2 Forum