iXtreme LT+ Lite Touch Xbox 360 Drive Firmware Flashing
Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1
    A Helping Hand
    Join Date
    Dec 2011
    Posts
    22
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Xbox 360 can't read any disk after upgrade to LT+2.0

    Hi, I am doing this for 1st time and need some help from you.

    Below are my xbox 360 spec.
    1. phat unit
    2. DG-16D2S-09c
    3. Dashboard - 2.0.13604.0

    I have upgrade my firmware to LT+ 2.0 (LTPlus-025-v2.0.bin), once I have completed the firmware upgrade. My xbox360 can't read any disk include dvd movie and it only show open tray and close tray. What is happening? Can anyone give some advice? Thanks!
    Last edited by cwyan; 12-11-2011 at 01:35 PM.

  2. #2
    Moderator
    Join Date
    Nov 2010
    Posts
    2,181
    Thanks
    8
    Thanked 221 Times in 218 Posts
    Did you flash they key over? Sent outro?

  3. #3
    Newbie
    Join Date
    Dec 2011
    Location
    Toronto, CA
    Posts
    0
    Thanks
    8
    Thanked 56 Times in 51 Posts
    Your drive is bricked because, you either pluged in the wire wrong, didnt hit outro or you didnt write anything at all

  4. #4
    Newbie
    Join Date
    Jun 2011
    Posts
    2
    Thanks
    0
    Thanked 0 Times in 0 Posts
    You forgot to connect the sata cable to the drive inside the box after you finished with the flashing. Just open the box, connect the cable and you are good to go
    Hail to the king, baby!

  5. #5
    A Helping Hand
    Join Date
    Dec 2011
    Posts
    22
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi all, thanks for reply!

    I am still having the same problem, after refresh to the LT+ 2.0 few times. I only can open/close tray in dashboard but can't read any disk include dvd movie.

    I am using x360usb pro and CK3i (just receive it)

    I have confirm that I have :
    1.flash the key over. (unless my understand is wrong, can you give more details?)
    2. I send outro
    3. I have plug in the SATA cable into my xbox360.


    Please refer to below for the JF log file.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    JungleFlasher 0.1.90 Beta (292)

    Session Started Mon Dec 12 03:25:54 2011



    This is a 32 bit process running on 2 x 32 bit CPUs

    X360USB PRO detected, Version 0.18



    portio32.sys Driver not Installed

    Found 5 I/O Ports.

    Found 1 Com Ports.

    Found 6 windows drives C: F: M: P: R: Z:

    Found 0 CD/DVD drives F: Z:



    Loading firmware file C:\Documents and Settings\chow\Desktop\xbox\JungleFlasher.0.1.90.Be ta(292)\JungleFlasher v0.1.90 Beta (292)\firmware\LTPlus-025-v2.0.bin

    MD5 hash: 0264149996f783b54629c1598072e50e

    Genuine LT plus v2.0

    Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

    Firmware Osig: [PLDS DG-16D2S 0251]

    Firmware is: LT-Plus 2.0

    Loading firmware file C:\xbox\Dummy.bin

    MD5 hash: 3173d120e84bf22dac2c4ab956020837

    Inquiry string found

    Identify string found

    Drive key @ 0xA030 E793562CD56943A42067EAF6F00AAAB

    Firmware Osig: [PLDS DG-16D2S 0251]

    Firmware is: PhatKey Extract

    Loading firmware file C:\Documents and Settings\chow\Desktop\xbox\JungleFlasher.0.1.90.Be ta(292)\JungleFlasher v0.1.90 Beta (292)\firmware\LTPlus-025-v2.0.bin

    MD5 hash: 0264149996f783b54629c1598072e50e

    Genuine LT plus v2.0

    Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

    Firmware Osig: [PLDS DG-16D2S 0251]

    Firmware is: LT-Plus 2.0

    Spoofing Target

    DVD Key copied to target

    Target is LT - ID strings not copied to Target

    Serial data already matches



    Target rev is LT 02510C, serial info not copied



    Sending Lite-On-Erase request to port 0x0000

    ..............

    Drive returned Status 0x90

    .............

    Serial flash found with Status 0x72

    Manufacturer ID: 0xC2

    Device ID: 0x11

    Flash Name: MXIC(MX25L2005)

    Flash Size: 262144 bytes



    Getting Status from port 0x0000

    SPi flash found with Status 0x72



    Sending Chip Erase to Port 0x0000

    Erasing:

    Writing target buffer to flash

    Writing Bank 0: ................

    Writing Bank 1: ................

    Writing Bank 2: ................

    Writing Bank 3: ................



    Flash Verification Test !

    Reading Bank 0: ................

    Reading Bank 1: ................

    Reading Bank 2: ................

    Reading Bank 3: ................

    Write verified OK !



    Sending Vendor Outro to port 0x0000

    Drive is Lite-On..



    Key found in KeyDB at record (1 - firmware)

    Key is: E793562CD56943A42067EAF6F00AAAB

    Key has been tested and verified, thanks C4eva !
    Last edited by cwyan; 06-16-2012 at 07:45 AM.

  6. #6
    A Helping Hand
    Join Date
    Dec 2011
    Posts
    22
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi, i suspect maybe i have extract the wrong dummy.bin. I having extract the dummy.bin after i have updated to Dashboard - 2.0.13604.0, am i extract the correct dummy.bin? Thanks!

  7. #7
    A Helping Hand
    Join Date
    Dec 2011
    Posts
    22
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi all. Any idea?

  8. #8
    Legend
    Join Date
    Jul 2011
    Location
    newcastle uk
    Posts
    3,578
    Thanks
    75
    Thanked 544 Times in 522 Posts
    nope, laser/drive problem, also dont bump your own threads please matey. did you disconnect laser ribbons before flashing?
    Newcastle Flashing
    Don't thank me, thank my THANKS button!!

    Quote Originally Posted by ultragamer View Post
    at least that reatard teached me something
    ...shame it wasn't how to spell...

  9. #9
    A Helping Hand
    Join Date
    Dec 2011
    Posts
    22
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by jamesyboiii View Post
    nope, laser/drive problem, also dont bump your own threads please matey. did you disconnect laser ribbons before flashing?
    Hi Jamesboiii. Sorry! I am new for flashing xbox 360, what you mean disconnect laser ribbons? The drive is working fine before I flash it, no sure what is goiong on! I have spend $100 to buy those equipment (xbox 360 usb pro and ect), at the end i have spoil the drive. Better pay someone to do it. Thanks!
    Last edited by cwyan; 12-13-2011 at 11:50 AM.

  10. #10
    Moderator
    Join Date
    Nov 2010
    Posts
    2,181
    Thanks
    8
    Thanked 221 Times in 218 Posts
    That means you didn't Which may be the cause of your laser getting weaker = reading discs slower or with more trouble. The ribbon is this

    http://www.team-xecuter.com/epoxy/07.jpg

Page 1 of 2 12 LastLast

Similar Threads

  1. Disk Read Errors
    By immortalbrute in forum 360 Backups
    Replies: 6
    Last Post: 08-07-2011, 11:52 AM
  2. My Xbox 360 wont read backed up disk please help
    By sicaudio in forum Don't waste that Dual Layer Disc
    Replies: 5
    Last Post: 04-20-2011, 06:19 AM
  3. Liteon can't read ANY disk
    By SeeJ in forum iXtreme LT+ Lite Touch Firmware Phat Support
    Replies: 6
    Last Post: 04-11-2011, 01:38 PM
  4. Disk not being read
    By afulker89 in forum Open Forum
    Replies: 2
    Last Post: 12-01-2010, 01:38 PM
  5. Can I get banned with a hard disk upgrade ?
    By tjaxbr in forum Downloads and Tutorials
    Replies: 6
    Last Post: 10-01-2009, 03:26 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
1e2 Forum